![]() The X-10 Bridge converts X-10 signals to Z-Wave technology so you can still use what you have and simply add to it with the Wayne-Dalton Home Control system.Ī: Yes. ¼ turn will equal 1” less door travel.Ī: No, the operator is not designed for a one piece door and the safety features will not work properly if installed on a one piece doorĪ: No, photoeyes are safety sensors and need to be mounted no more than 5" above the floor to the center line of the safety sensor bracket.Ī: No, photo eye safety sensors are required on all Quantum, Classic Drive and prodrive operators are requiredĪ: No, this is a potential safety issue and a code violation.Ī: You only need an X-10 Bridge if you have an existing home automation system that utilizes this technology. Turn the “OPEN” travel adjustment screw at the bottom of the operator clockwise to decrease amount of open door travel. Q: Where can I buy replacement parts for my prodrive model?Ī: The most likely cause is the open travel limit is set too far open and the carriage is striking the stop bolt. Q: What is the battery life on the transmitters? Keyless entry? Wireless Wall station? Q: My door will not close, from open it travels a short distance downward and then reverse to full open, what is the problem? Q: My door travels closed but stops and reverses to full open before it reaches the floor, what is the problem? Q: My door travels all the way to the floor then reverses and returns to full open, what is the problem? Q: My door stops short of the floor, what is the problem? Q: My door does not open all the way and the light flashes after it stops, what is the problem? Q: My door does not open all the way and the light does not flash after it stops, what is the problem? Q: Is my operator Z-wave (Home Access) compatible? Q: How many Wall Stations can I program into my operator Q: How many transmitters can I program into my opener? Q: How many keyless entry's can I program into my operator? ![]() Q: How far away from my door should I be able to operate my door using a remote? Q: How do I teach my wireless wall station to my operator? Q: How do I teach a remote to my operator? Q: How do I determine what radio frequency my operator is? Q: Does Wayne-Dalton produce Fiberglass Garage Doors? Q: Can I run my operator from an extension cord? Q: Can I operate my opener without the photo eyes? Q: Can I mount the photo eyes high above the door to get them out of site? Q: Can I install my operator on a one piece door? Q: After my door opens the light flashes on and off for a minute, how do I correct this? For 372 Mhz frequency the antenna wire color is - Single wire - yellow.Solution home FAQ Wayne Dalton Prodrive You can look at the color of the antenna wire coming out of the powerhead unit to determine the frequency. If you have a remote control check on the back of it for the frequency number. On the back of your garage door opener motor (attached to the ceiling in your garage) there should be a silver sticker which has the model number of your garage door opener written on it. Will this wall station work with my garage door opener model? Wayne Dalton Doormaster BDOR-2000 models using 372 Mhz with yellow antenna wire.Wayne Dalton Classic Drive models 3014, 3018, 3514.Works with all Wayne Dalton Garage Door Opener models that use frequency 372 Mhz. Vacation Slide-Lock: Disables remote transmitters, keyless entries and wall stations.Programmable pet opening (Opens to a pre-selected height of 6"-30").Wireless, for easy installation anywhere.Replaces old 5-function wall station 300644 This Wireless Wall Station is made exclusively for Wayne Dalton Classic Drive, Quantum, idrive, Doormaster, Prodrive garage door openers (models using 372 Mhz frequency). Replace with Wired Wall Station 309961 (not compatible with iDrive models) Wayne Dalton Wireless Deluxe Wall Station 311365 327314 is a 7-Function Deluxe Wireless Multi Function Wall Station (372 Mhz)ĭiscontinued.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |